CISCO router license activated 2013 version

Speaking of it that I configured an afternoon to configure the activation of this license on yesterday afternoon starting from 1 pm until the last few minutes at 5 pm. I thought it would be too simple to apply for a license on the CISCO website. I believe that everyone has upgraded the license of ASA K8 to K9 on the CISCO website. It is a very simple matter but it has encountered a license upgrade after CISCO's revision. However, no matter how I apply, it is the last step and it hangs. The situation is follows below:

 When I generated the license file finally, I stopped it. I always thought it was a problem with the CISCO website because everyone knows that the website is very slow, especially downloading I0S which is quite slow. However, after waiting for ten minutes, it is not normal to  repeat Test but I can't generate a license file. I can't understand it. I don't understand that there is a problem. Repeated application is still unsuccessful.

Then, I started looking for documents on the Internet to see if there were any solutions. The results were searched online and only two are introducing this upgrade but the version does not encounter such a problem at all. I also read a piece of text that puts me under pressure:

When filling in the PID and SN in the third step, you must not fill in the wrong one. PAK can only be used once. If the PID and SN are incorrectly filled. It is necessary to open CASE to CISCO. It is very troublesome and wastes time, such as some modular routing. Switching devices have many PIDs and SNs. For example, there are chassis, engine, power, no matter how many but as long as you execute the show license udi command to see which it is. This time I did not find the official information before entering the chassis PID and SN. The result is a living the license file is reported incorrectly when it is installed in the router. Finally, it is still very troublesome to write an email to license@cisco.com so be sure to fill it out correctly.

Why is there pressure? Because I seem to fill in PID and SN several times before and after. And the first time I wrote it was definitely wrong. I thought all the things are over. I won’t really have to open CASE to get it and the settler is still waiting to use it. Everyone knows such a simple question that repeated several times unsuccessful will inevitably be very impatient. I am no exception about that. At the documentation on the website of CISCO, everyone knows how slow CISCO's documentation is updated. There are no ready-made documents like this and it has suddenly entered the dead hole.

I asked a few friends online that everyone has not upgraded this new version but it is impossible to make this unclear. I have been unclear. My approach should be no problem and not wrong but I don’t know why. In the end, I found a good one. I asked about it because he had applied for it. I also saw it on the side so I knew that his activation was successful. The two of us carefully compared my own practices and found that the process was the same but in the end it is no and do not have any reason for that.

Finally, the problem is  found. The reason is my google browser. When my friend uses IE browser, there is no problem that he can succeed but only my cannot. Then, I found that when you use IE, there will be such a prompt:

However, when browsing with google, there is no such prompt. After the problem was found that I was speechless.

The specific method is as follows:

First go to www.cisco.com/go/license and you can see the following tips:

 

The second step is to fill in the PAK number. It is on a piece of white paper that you get and the white one is the PAK number.

As shown

 

Now you can get the two values of the router's PID and SN by the command sh license udi on the device. Don't make mistakes in these two numbers otherwise it will be very troublesome.

Compare the above SN number. Don't make a mistake.

The model must be selected before you can choose the next step.

The last step is to the generate the license file, you will be asked to fill in the email address. This is not wrong. There are two kinds, one is to send you an email and the other is to download directly and generally choose to download Yes. I was there no way at the time.

It is obvious that the mail has received the license file.

Don't say it again! Copy it to FLASH and then upgrade it is like this. From the above, you can see that there is a license for the basic version as well as a license for security and data versions.

 The above content must be known as a CCIE. If you still feel that the CCIE written exam and CCIE LAB exam are difficult to pass, then join PASSHOT. We will let you  more easily to pass the CCIE exam.